1064922 Phoenix Contact AC/DC Power Supplies

Product Details

• Installation distance top/bottom
  50 mm / 50 mm
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Discharge current to PE
  < 0.25 mA
• Current consumption
  3x 0.4 A (400 V AC)
• Power factor (cos phi)
  0.55
• Protection against overvoltage at the output (OVP)
  ≤ 30 V DC
• Output power
  120 W
• Efficiency
  typ. 91 % (400 V AC)
• Insulation voltage input/output
  3 kV AC (type test)
• Conductor cross section flexible min.
  0.2 mm²
• EMC requirements for noise immunity
  EN 61000-6-2
• Standard - Electrical safety
  IEC 61010-1 (SELV)
• UL approvals
  UL Listed UL 61010-2-201
• Electrostatic discharge
  EN 61000-4-2
• Frequency range
  80 MHz ... 6 GHz
• Comments
  Criterion A
• Frequency
  50 Hz
• Additional text
  Test Level 2
• Criterion B
  Temporary impairment to operational behavior that is corrected by the device itself.
• ETIM 6.0
  EC002540
Width
36 mm
Installation distance right/left (active)
14 mm / 14 mm
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Degree of pollution
2
Nominal power consumption
243.6 VA
Mains buffering time
typ. 20 ms (400 V AC)
Connection in parallel
Yes, for redundancy and increased capacity
Typical response time
< 1 s
Power loss nominal load max.
< 12 W (480 V AC)
Connection method
Push-in connection
Conductor cross section AWG max.
16
Standard – Safety extra-low voltage
IEC 61010 (SELV) / (PELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Conducted noise emission
EN 55016
Test field strength
10 V/m (Test Level 3)
Input
3 kV (Test Level 3 - symmetrical)
Signal
1 kV (Test Level 1 - symmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 10.0.1
27040701
ECLASS 11.0
27040701
ECLASS 9.0
27040701
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Installation distance top/bottom (active)
50 mm / 50 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Installation height
≤ 4000 m (> 2000 m, Derating: 10 %/1000 m)
Protective circuit/component
Varistor
Setting range of the output voltage (USet)
24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
Connection in series
yes
Residual ripple
≤ 20 mVPP
MTBF (IEC 61709, SN 29500)
> 2300000 h (25 °C)
Conductor cross section solid max.
1.5 mm²
Conductor cross section AWG min.
24
Standard - Safe isolation
DIN VDE 0100-410
Height
160 mm
Installation distance right/left
0 mm / 0 mm
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Nominal input voltage range
3x 400 V AC ... 500 V AC
AC frequency range
50 Hz ... 60 Hz
Input fuse
3.15 A (internal (device protection), slow-blow)
Nominal output current (IN)
5 A
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Net weight
0.7 kg
Protection class
II (in closed control cabinet)
Conductor cross section solid min.
0.2 mm²
Stripping length
8 mm
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Noise emission
EN 55016
Discharge in air
8 kV (Test Level 4)
Output
1 kV (Test Level 2 - symmetrical)
Voltage dip
0 %
Voltage
230 V AC
Number of periods
1 period
REACh SVHC
Lead 7439-92-1
ETIM 7.0
EC002540
Depth
159 mm
Degree of protection
IP20
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
3x 400 V AC ... 500 V AC -20 % ....+15 %
Type of protection
Transient surge protection
Nominal output voltage
24 V DC ±1 %
Dynamic Boost (IDyn.Boost)
7.5 A (5 s)
Derating
> 60 °C ... 70 °C (2.5%/K)
Maximum power dissipation in no-load condition
< 1 W (400 V AC)
Assembly instructions
Cross Power System
Conductor cross section flexible max.
1.5 mm²
Standard - Safety of transformers
EN 61558-2-16 (air clearances and creepage distances only)
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Contact discharge
6 kV (Test Level 4)
Electromagnetic HF field
EN 61000-4-3
Fast transients (burst)
EN 61000-4-4
Conducted interference
EN 61000-6-2
Voltage dips
EN 61000-4-11
ECLASS 6.0
27049000
ECLASS 7.0
27049002