2320115 Phoenix Contact DC/DC Converters

Product Details

• Height
  130 mm
• Height with alternative assembly
  130 mm
• Installation distance right/left
  0 mm / 0 mm (≤ 70 °C)
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C derating, 2.5 %/K, startup at -40°C type-tested)
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Nominal input voltage range
  24 V DC
• Extended input voltage range in operation
  14 V DC ... 18 V DC (Consider derating during operation)
• Inrush current
  < 15 A (typical)
• Setting range of the output voltage (USet)
  5 V DC ... 18 V DC (> 12 V DC, constant capacity restricted)
• POWER BOOST (IBoost)
  10 A (-25 °C ... 40 °C permanent, UOUT = 12 V DC )
• Derating
  60 °C ... 70 °C (2.5%/K)
• Connection in series
  yes
• Control deviation
  < 1 % (change in load, static 10 % ... 90 %)
• Width
  32 mm
• Width with alternative assembly
  122 mm
• Installation distance top/bottom
  50 mm / 50 mm (≤ 70 °C)
• Degree of protection
  IP20
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Degree of pollution
  2
• Current consumption
  6 A (24 V, IBOOST)
Mains buffering time
> 10 ms (24 V DC)
Type of protection
Transient surge protection
Nominal output current (IN)
8 A (-25 °C ... 60 °C)
Selective Fuse Breaking (ISFB)
48 A (12 ms)
Feedback voltage resistance
25 V DC
Max. capacitive load
unlimited
Peak switching voltages nominal load
< 10 mVPP (20 MHz)
Power loss nominal load max.
10.5 W
Depth
125 mm
Depth with alternative assembly
35 mm
Installation distance top/bottom (active)
50 mm / 50 mm (≤ 70 °C)
Installation distance right/left (active)
15 mm / 15 mm (≤ 70 °C)
Ambient temperature (start-up type tested)
-40 °C
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
18 V DC ... 32 V DC
Input fuse
15 A (internal (device protection))
Protective circuit/component
Varistor
Nominal output voltage
12 V DC ±1 %
Connection in parallel
Yes, for redundancy and increased capacity
Protection against overvoltage at the output (OVP)
< 25 V DC
Active current limitation
15 A
Residual ripple
< 20 mVPP
Net weight
0.7 kg
Insulation voltage input/output
1.5 kV (type test)
Conductor cross section solid min.
0.2 mm²
Conductor cross section flexible max.
2.5 mm²
Conductor cross section AWG max.
12
Screw thread
M3
EMC requirements for noise immunity
EN 61000-6-1
UL approvals
UL/C-UL listed UL 508
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Comments
Criterion A
Surge voltage load (surge)
EN 61000-4-5
Voltage
10 V (Test Level 3)
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 11.0
27210901
ECLASS 5.0
27210900
ETIM 4.0
EC002542
UNSPSC 11
39121004
UNSPSC 19.0
39121041
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Electrostatic discharge
EN 61000-4-2
Electromagnetic HF field
EN 61000-4-3
Frequency range
0.15 MHz ... 80 MHz
Input
1 kV (Test Level 2 - symmetrical)
Output
1 kV (Test Level 2 - symmetrical)
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
27210900
ETIM 7.0
EC002046
UNSPSC 7.0901
39121004
UNSPSC 18.0
39121041
UNSPSC 21.0
39121041
Maximum power dissipation in no-load condition
2 W
Efficiency
> 90 %
Protection class
III
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Conductor cross section flexible min.
0.2 mm²
EMC requirements for noise emission
EN 61000-6-3
Standard - Electrical safety
EN 60950-1/VDE 0805 (SELV)
Standard - Safe isolation
DIN VDE 0100-410
Shipbuilding approval
DNV GL (EMC B)
Discharge in air
15 kV (Test Level 4)
Test field strength
10 V/m
Signal
1 kV (Test Level 2 - asymmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 10.0.1
27210901
ECLASS 6.0
27210900
ECLASS 7.0
27210901
ETIM 6.0
EC002046
UNSPSC 13.2
39121041
Mounting position
horizontal DIN rail NS 35, EN 60715
Connection method
Pluggable screw connection
Conductor cross section solid max.
2.5 mm²
Conductor cross section AWG min.
24
Stripping length
7 mm
Standard – Safety extra-low voltage
EN 60950-1 (SELV)
Rail applications
EN 50121-4
Contact discharge
8 kV (Test Level 4)
Fast transients (burst)
EN 61000-4-4
I/O/S
asymmetrical
Criterion A
Normal operating behavior within the specified limits.
ECLASS 4.0
27210900
ECLASS 5.1
27210900
ECLASS 9.0
27210901
UNSPSC 6.01
30211502
UNSPSC 12.01
39121004
UNSPSC 20.0
39121041