2903151 Phoenix Contact AC/DC Power Supplies

Product Details

• ECLASS 9.0
  27040701
• Width
  68 mm
• Installation distance top/bottom
  50 mm / 50 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Installation height
  ≤ 4000 m (> 2000 m, Derating: 10 %/1000 m)
• Nominal power consumption
  534.7 VA
• Mains buffering time
  typ. 10 ms (120 V AC)
• Setting range of the output voltage (USet)
  24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
• Connection in series
  yes
• Feedback voltage resistance
  ≤ 35 V DC
• Net weight
  1.5 kg
• Conductor cross section solid min.
  0.2 mm²
• Conductor cross section AWG max.
  16
• Standard – Limitation of mains harmonic currents
  EN 61000-3-2
• Low Voltage Directive
  Conformance with Low Voltage Directive 2014/35/EC
• Contact discharge
  6 kV (Test Level 4)
• Output
  1 kV (Test Level 2 - symmetrical)
• Voltage
  10 V (Test Level 3)
• ECLASS 4.1
  27040702
• ECLASS 6.0
  27049002
Depth
160 mm
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Nominal input voltage range
100 V AC ... 240 V AC
Discharge current to PE
< 3.5 mA
Inrush current
≤ 20 A (typical)
Protective circuit/component
Varistor
Derating
> 60 °C ... 70 °C (2.5%/K)
Residual ripple
< 100 mVPP (with nominal values)
Output power
480 W
MTBF (IEC 61709, SN 29500)
> 1800000 h (25 °C)
Mounting position
horizontal DIN rail NS 35, EN 60715
Connection method
Push-in connection
Conductor cross section AWG min.
24
Standard - Safety of transformers
EN 61558-2-16 (air clearances and creepage distances only)
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
UL approvals
UL Listed UL 508
Noise emission
EN 55016
Comments
Criterion A
Input
3 kV (Test Level 3 - symmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 11.0
27040701
AC frequency range
50 Hz ... 60 Hz ±10 %
Type of protection
Transient surge protection
Nominal output voltage
24 V DC ±1 %
Dynamic Boost (IDyn.Boost)
30 A (5 s)
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Typical response time
< 1 s
Insulation voltage input/output
3 kV AC (type test)
Efficiency
typ. 91.4 % (120 V AC)
Height
130 mm
Degree of protection
IP20
Ambient temperature (start-up type tested)
-40 °C
Degree of pollution
2
Dielectric strength maximum
≤ 300 V AC 15 s
Input fuse
10 A (internal (device protection))
Recommended breaker for input protection
10 A ... 16 A (Characteristics B, C, D, K)
Connection in parallel
Yes, for redundancy and increased capacity
Protection against overvoltage at the output (OVP)
≤ 30 V DC
Power loss nominal load max.
< 44.8 W (120 V AC)
Assembly instructions
alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
Conductor cross section solid max.
1.5 mm²
Electrostatic discharge
EN 61000-4-2
Discharge in air
8 kV (Test Level 4)
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 4.0
27040702
ECLASS 5.0
27049002
UNSPSC 13.2
39121004
Installation distance right/left
0 mm / 0 mm
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Current consumption
5.6 A (100 V AC)
Power factor (cos phi)
0.98
Nominal output current (IN)
20 A
Maximum power dissipation in no-load condition
< 2.9 W (120 V AC)
Protection class
I (in closed control cabinet)
Conductor cross section flexible max.
1.5 mm²
EMC requirements for noise immunity
EN 61000-6-1
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
Standard – Safety extra-low voltage
IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Shipbuilding approval
DNV GL
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electromagnetic HF field
EN 61000-4-3
Fast transients (burst)
EN 61000-4-4
Surge voltage load (surge)
EN 61000-4-5
ECLASS 10.0.1
27040701
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 7.0
27049002
UNSPSC 19.0
39121004
Conductor cross section flexible min.
0.2 mm²
Stripping length
8 mm
EMC requirements for noise emission
EN 61000-6-3
Standard - Safe isolation
DIN VDE 0100-410
Rail applications
EN 50121-4
Conducted noise emission
EN 55016
Frequency range
0.15 MHz ... 80 MHz
Test field strength
10 V/m (Test Level 3)
Signal
1 kV (Test Level 2 - asymmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 5.1
27049002
ETIM 6.0
EC002540
ETIM 4.0
EC002540