2909577 Phoenix Contact AC/DC Power Supplies

Product Details

• Installation distance top/bottom
  30 mm / 30 mm
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Input voltage range
  100 V AC ... 240 V AC -15 % ... +10 %
• Inrush current
  typ. 13 A (at 25 °C)
• Input fuse
  3.15 A (slow-blow, internal)
• Setting range of the output voltage (USet)
  24 V DC ... 28 V DC (constant capacity)
• Protection against overvoltage at the output (OVP)
  ≤ 32 V DC
• Residual ripple
  < 45 mVPP (with nominal values)
• Net weight
  0.296 kg
• Width
  45 mm
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Installation height
  ≤ 5000 m (> 2000 m, observe derating)
• Frequency range (fN)
  50 Hz ... 60 Hz -10 % ... +10 %
• Mains buffering time
  typ. 35 ms (120 V AC)
• Type of protection
  Transient surge protection
• Derating
  > 60 °C (2.5%/K)
• Control deviation
  < 0.5 % (Static load change 10 % ... 90 %)
• Output power
  90 W
• Environmental protection directive
  RoHS Directive 2011/65/EU
• Connection method
  Push-in connection
Conductor cross section AWG max.
14
Standard – Safety extra-low voltage
IEC 61010-1 (SELV)
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Discharge in air
8 kV (Test Level 3)
Surge voltage load (surge)
EN 61000-4-5
Power frequency magnetic field
EN 61000-4-8
Additional text
Test Level 2
Test level 2
16.67 Hz 50 Hz 60 Hz (Test Level 4)
Attenuated oscillating wave
EN 61000-4-18
ECLASS 11.0
27040701
ETIM 7.0
EC002540
UNSPSC 21.0
39121004
Depth
90 mm
Installation distance right/left
0 mm / 0 mm
Ambient temperature (start-up type tested)
-40 °C
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Degree of pollution
2
Current consumption
1 A (100 V AC)
Nominal power consumption
104 VA
Nominal output voltage
24 V DC
Dynamic Boost (IDyn.Boost)
7 A (≤ 60 °C (5 s))
Connection in parallel
Yes, for redundancy and increased capacity
Feedback voltage resistance
≤ 35 V DC
Maximum power dissipation in no-load condition
< 1 W (120 V AC)
Efficiency
typ. 92.8 % (120 V AC)
Insulation voltage input/output
4 kV AC (type test)
Conductor cross section flexible max.
2.5 mm²
Conductor cross section flexible min.
0.2 mm²
Standard - Electrical safety
IEC 61010-2-201 (SELV)
Standard - Safety of transformers
EN 61558-2-16
UL approvals
UL Listed UL 61010-1
SIQ
CB-Scheme (IEC 61010-1, IEC 61010-2-201)
Noise emission
EN 55016
Fast transients (burst)
EN 61000-4-4
Input
2 kV (symmetrical)
Conducted interference
EN 61000-4-6
Number of periods
0.5 / 1 / 5 / 50 periods
Test level 1
16.67 Hz 50 Hz 60 Hz (Test Level 3)
ECLASS 10.0.1
27040701
ECLASS 9.0
27040701
UNSPSC 20.0
39121004
Height
106 mm
Climatic class
3K3 (in acc. with EN 60721)
Dielectric strength maximum
300 V AC 30 s
Protective circuit/component
Varistor
Nominal output current (IN)
3.8 A
Power loss nominal load max.
< 7 W (120 V AC)
Protection class
II
Conductor cross section AWG min.
24
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
Conducted noise emission
EN 55016
Electrostatic discharge
EN 61000-4-2
Comments
Criterion B
I/O/S
asymmetrical
Voltage dip
0 %
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
REACh SVHC
Lead 7439-92-1
ETIM 6.0
EC002540
UNSPSC 13.2
39121004
Degree of protection
IP20
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Discharge current to PE
< 0.25 mA (264 V AC, 60 Hz)
Recommended breaker for input protection
6 A ... 16 A (Characteristic B, C, D, K or comparable)
Connection in series
yes
Typical response time
500 ms
MTBF (IEC 61709, SN 29500)
> 1272000 h (25 °C)
Conductor cross section solid max.
2.5 mm²
EMC requirements for noise immunity
EN 61000-6-1
Standard - Safe isolation
IEC 61558-2-16
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electromagnetic HF field
EN 61000-4-3
Frequency range
50 Hz ... 60 Hz
Signal
0.5 kV (Test Level 2 - symmetrical)
Frequency
60 Hz
Pulse-shape magnetic field
EN 61000-4-9
Criterion A
Normal operating behavior within the specified limits.
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 5.1
27242213
ECLASS 7.0
27049002
UNSPSC 19.0
39121004
Assembly instructions
DIN rail mounting
Conductor cross section solid min.
0.2 mm²
Stripping length
10 mm
EMC requirements for noise emission
EN 61000-6-3
Standard - power supply devices for low voltage with DC output
EN 61204-3
Contact discharge
8 kV (Test Level 4)
Test field strength
1000 A/m
Output
1 kV (Test Level 3 - symmetrical)
Voltage
300 V (1 s)
Voltage dips
EN 61000-4-11
Asymmetrical conducted disturbance variables
EN 61000-4-16
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.
ECLASS 6.0
27049000
UNSPSC 18.0
39121004