X20CP1301 B&R Electronic Components

Product Details

• Weight300 g
• Temperature Operation Vertical mounting orientation
  -25 to 50°C
• Temperature Operation Horizontal mounting orientation
  -25 to 60°C
• Max. error Current Offset
  0 to 20 mA = 0.1% (Rev.
• Max. error Voltage Gain
  0.18% (Rev.
• Max. error Current Gain
  0 to 20 mA = 0.15% (Rev.
• Max. error Voltage Offset
  0.04% (Rev.
• Interface IF2 Transfer Auto-MDI/MDIX
  Yes
• Interface IF2 Transfer Autonegotiation
  Yes
• Interface IF2 Transfer Full-duplex
  Yes
• Interface IF2 Transfer Physical layer
  10BASE-T/100BASE-TX
• Interface IF2 Transfer Half-duplex
  Yes
• Application memory Writable data amount Results for 5 years
  21.9 GB/day
• Processor L1 cache Program code
  16 kB
• Application memory Writable data amount Guaranteed
  40 TB
• Processor L1 cache Data code
  16 kB
• Dimensions Height
  99 mm
• Dimensions Depth
  75 mm
• Dimensions Width
  164 mm
• Relative humidity Storage
  5 to 95%, non-condensing
Relative humidity Transport
5 to 95%, non-condensing
Relative humidity Operation
5 to 95%, non-condensing
Temperature Transport
-40 to 85°C
Temperature Derating
See section "Switching frequency derating for high-speed digital outputs".
Temperature Storage
-40 to 85°C
Installation elevation above sea level >2000 m
Reduction of ambient temperature by 0.5°C per 100 m
Mounting orientation Horizontal
Yes
Installation elevation above sea level 0 to 2000 m
No limitation
Mounting orientation Vertical
Yes
Switching frequency Inductive load
See section "Switching inductive loads".
Switching frequency Resistive load
Standard outputs and mixed channels: Max. 500 Hz; High-speed outputs: 50 kHz, max. 200 kHz (see section "Switching frequency derating for high-speed digital outputs")
Switching delay 1 → 0
Standard outputs and mixed channels: <300 µs; High-speed outputs: <3 µs
Switching delay 0 → 1
Standard outputs and mixed channels: <300 µs; High-speed outputs: <3 µs
Pulse width modulation Resolution for pulse duration
0.1% of the configured frequency
Temperature sensor normalization Pt1000
-200 to 850°C
Pulse width modulation Pulse duration
0 to 100%, minimum 2.5 µs
Pulse width modulation Period duration
5 to 65535 µs corresponds to 200 kHz to 15 Hz
Max. error at 25°C Offset
0.15% (Rev.
Max. error at 25°C Gain
0.3% (Rev.
Sensor Pt1000
-200 to 850°C
Nonlinearity Voltage
<0.025%
Nonlinearity Current
<0.05%
Common-mode rejection 50 Hz
70 dB
Common-mode rejection DC
70 dB
Max. offset drift Current
0 to 20 mA = 0.008 %/°C / 4 to 20 mA = 0.012 %/°C
Max. offset drift Voltage
0.008 %/°C
Max. gain drift Current
0 to 20 mA = 0.015 %/°C / 4 to 20 mA = 0.023 %/°C
Permissible input signal Current
Max. ±50 mA
Max. gain drift Voltage
0.017 %/°C
Permissible input signal Voltage
Max. ±30 V
Load Voltage
-
Input impedance in signal range Current
-
Load Current
<300 Ω
Input impedance in signal range Voltage
20 MΩ
Output format Current
INT 0x0000 - 0x7FFF / 1 LSB = 0x0008 = 4.883 μA
Output format Voltage
INT 0x8001 - 0x7FFF / 1 LSB = 0x0008 = 2.441 mV
Digital converter resolution Current
12-bit
Output format Data type
INT
Digital converter resolution Voltage
±12-bit
Switching threshold High
>15 VDC
Switching threshold Low
<5 VDC
Input filter Software
Default 1 ms, configurable between 0 and 25 ms in 0.1 ms increments
Interface IF4 Max. output current
0.5 A
Input filter Hardware
Standard inputs and mixed channels: ≤200 μs; High-speed inputs: ≤2 μs, when used as standard inputs: ≤200 μs
Interface IF6 Fieldbus
X2X Link master
Interface IF4 Variant
Type A
Interface IF2 Line length
Max. 100 m between 2 stations (segment length)
Interface IF4 Type
USB 1.1/2.0
Interface IF2 Transfer rate
10/100 Mbit/s
Interface IF2 Variant
1x RJ45 shielded
Interface IF2 Signal
Ethernet
Interface IF1 Transfer rate
Max. 115.2 kbit/s
Interface IF1 Max. distance
900 m
Interface IF1 Signal
RS232
Interface IF1 Variant
Connection via 16-pin terminal block X20TB1F
Application memory Error-correcting code (ECC)
Yes
Application memory Guaranteed erase/write cycles
20,000
Application memory Type
1 GB eMMC flash memory
Application memory Data retention
10 years
Standard memory RAM
128 MB DDR3 SDRAM
Processor L2 cache
128 kB
Processor Clock frequency
200 MHz
Certifications ABS
Yes
Certifications EAC
Yes
Processor Type
Vx86EX
Certifications LR
ENV1
Certifications KR
Yes
Certifications DNV
Temperature: B (0 - 55°C); Humidity: B (up to 100%); Vibration: B (4 g); EMC: B (bridge and open deck)
Certifications HazLoc
cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
Certifications UL
cULus E115267; Industrial control equipment
Certifications ATEX
Zone 2, II 3G Ex nA nC IIA T5 Gc; IP20, Ta (see X20 user's manual); FTZÚ 09 ATEX 0083X
Certifications UKCA
Yes
Support Visual Components support
Yes
Certifications CE
Yes
Power consumption Internal I/O
2.3 W
Support Controller redundancy
No
Support ACOPOS support
Yes
Support reACTION-capable I/O channels
No
Diagnostics RS232 data transfer
Yes, using LED status indicator
Diagnostics I/O power supply
Yes, using LED status indicator
Diagnostics Temperature
Yes, using software register
Diagnostics Supply voltage monitoring
Yes, using LED status indicator
Diagnostics Ethernet
Yes, using LED status indicator
Diagnostics CPU function
Yes, using LED status indicator
Diagnostics Inputs
Analog inputs: Yes, using LED status indicator and software
Diagnostics Outputs
Digital outputs: Yes, using LED status indicator and software (output error status)
Note
X20 end cover plate (right) included in delivery; 3 X20 terminal blocks (16-pin) included in delivery; Interface module slot cover included in delivery
Electrical isolation
Ethernet (IF2) and X2X (IF6) isolated from each other, from other interfaces and from PLC; Channel isolated from bus; Channel not isolated from channel or PLC
Braking voltage when switching off inductive loads
Standard outputs and mixed channels: Typ. 45 VDC
Switch-on in the event of overload shutdown or short-circuit shutdown
Standard outputs and mixed channels: Approx. 10 ms (depends on module temperature); High-speed outputs: No switch-on
Degree of protection per EN 60529
IP20
Residual voltage
Standard outputs and mixed channels: <0.1 V at nominal current 0.5 A; High-speed outputs: <0.9 V at nominal current 0.1 A
Peak short-circuit current
Standard outputs and mixed channels: <3 A; High-speed outputs: <20 A
Leakage current when the output is switched off
Standard outputs and mixed channels: 5 µA; High-speed outputs: 25 µA
RDS(on)
140 mΩ
Output protection
Thermal shutdown in the event of overcurrent or short circuit (see value "Short-circuit peak current"); Internal freewheeling diode for switching inductive loads (see section "Switching inductive loads")
Diagnostic status
Standard outputs and mixed channels: Output monitoring with 10 ms delay; High-speed outputs: Output monitoring with 10 µs delay
Output circuit
Standard outputs and mixed channels: Source; High-speed outputs: Sink or source
Nominal output current
Standard outputs and mixed channels: 0.5 A; High-speed outputs: 0.2 A
Standardized range of values for resistance measurement
0.1 to 4000.0 Ω
Total nominal current
Standard outputs and mixed channels: 4 A; High-speed outputs: 0.8 A
Switching voltage
24 VDC -15% / +20%
Variant
Standard outputs and mixed channels: Current-sourcing FET; High-speed outputs: Push-Pull
Nonlinearity
<0.05%
Max. offset drift
0.012%/°C
Max. gain drift
0.023 %/°C
Permissible input signal
Short-term max. ±30 V
Measurement current
1 mA
Linearization method
Internal
Resistance measurement resolution
1 LSB = 0x0005 = 0.49 Ω
Sensor standard
EN 60751
Temperature sensor resolution
1 LSB = 0x0005 = 0.16°C
Resistance measurement range
0.1 to 4000 Ω
Output format
INT or UINT for resistance measurement
Digital converter resolution
13-bit
Common-mode range
±12 V
Crosstalk between channels
<-70 dB
Input filter
Third-order low-pass filter / Cutoff frequency 1 kHz
Conversion procedure
SAR
Output of digital value during overload
Configurable
Input protection
Protection against wiring with supply voltage
Input
±10 V or 0 to 20 mA / 4 to 20 mA, via different terminal connections
Input type
Differential input
Conversion time
1 channel enabled: 100 µs; 2 channels enabled: 200 µs
Timestamp
1 µs resolution
Measurements per module
Each function up to 2x
Signal form
Square wave pulse
Possible measurements
Period measurement, gate measurement, differential time measurement, edge counter, edge times
Overload characteristics of encoder power supply
Short-circuit proof, overload-proof
Counter frequency
250 kHz
Encoder power supply
Module-internal, max. 300 mA
Input frequency
Max. 100 kHz
Counter size
32-bit
Evaluation
4x
Encoder inputs
24 V, asymmetrical
Additional functions
X2 - High-speed digital inputs:; 2x 250 kHz event counting, 2x AB counter, ABR incremental encoder, direction/frequency, period measurement, gate measurement, differential time measurement, edge counters, edge times
Connection type
1-wire connections
Input resistance
X1 - Standard inputs: 6.8 kΩ; X2 - Standard inputs: 8.9 kΩ; X2 - High-speed inputs: 6.8 kΩ; X3 - Mixed channels: 8.9 kΩ
Nominal voltage
24 VDC
Input current at 24 VDC
X1 - Standard inputs: Typ. 3.5 mA; X2 - Standard inputs: Typ. 2.68 mA; X2 - High-speed inputs: Typ. 3.5 mA; X3 - Mixed channels: Typ. 2.68 mA
Input circuit
Sink
Remanent variables
16 kB FRAM, retention >10 years
Quantity
14 standard inputs, 4 high-speed inputs and 4 mixed channels, configuration as input or output using software
Shortest task class cycle time
2 ms
Typical instruction cycle time
0.0419 µs
Integrated I/O processor
Processes I/O data points in the background
Modular interface slots
1
Permissible contact load
10 A
Nominal output voltage
24 VDC
Fuse
Integrated, cannot be replaced
Parallel connection
Yes
Input current
Max. 1 A
Real-time clock
Retention for at least 300 hours, typ. 1000 hours at 25°C, 1 s resolution, -18 to 28 ppm accuracy at 25°C
Reverse polarity protection
Yes
Redundant operation
Yes
FPU
Yes
Nominal output power
2 W
Cooling
Fanless
Status indicators
CPU function, Ethernet, RS232, PLC power supply, I/O power supply, I/O function per channel
B&R ID code
0xE35B
Input voltage
24 VDC -15% / +20%
Interfaces
1x RS232, 1x Ethernet, 1x USB, 1x X2X Link
System module
Controller
Type of signal lines
Shielded lines must be used for all high-speed digital inputs/outputs, line length: Max. 20 m
Power consumption without interface module and USB
4.3 W
Power consumption for X2X Link power supply
0.8 W

Related documents X20CP1301 Specs