1270301 Phoenix Contact Electrical Wires & Cables

Product Details

• Application
  For charging with alternating current (AC) and with direct current (DC)
• Charging mode
  Mode 2, 3, 4
• Depth
  128.4 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Rated current for signal contacts
  2 A
• Type of signal transmission
  Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
• Insertion/withdrawal cycles
  > 10000
• Restrictions to mounting position
  Only 0 to 90 degree frontal inclination possible, see figure
• Material
  Plastic
• External cable diameter
  1.6 mm -0.2 mm
• External sheath, color
  Green-yellow
• Outer sheath, material
  PVC
• Number of positions of theconnectors
  4
• Maximum voltage for locking detection
  30 V
• Service life insertion cycles
  > 10000 load cycles
• Lock recognition
  available
• Standards/regulations
  DIN EN 60751
• Note on the connection method
  Crimp connection, cannot be disconnected
• Degree of protection
  IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
• Max. altitude
  4000 m (above sea level)
Number of signal contacts
2 (CP, PP)
Resistor coding
4.7 kΩ (between PE and PP)
Mounting hole diameter
6.80 mm (ø)
Screws included in the scope of delivery
none
Cable structure
4 x 0.5 mm²
Height
130.4 mm
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Maximum charging power
250 kW
Rated voltage for power contacts
480 V AC
Rated voltage for signal contacts
30 V AC
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Required mounting screws
M6
Housing color
black
Cable resistance
≤ 37.1 Ω/km
Possible power supply range at the motor
22 V ... 26 V
Pause time after entry or exit path
3 s
Tolerance at the sensor with the recommended measured current
±5K
ECLASS 9.0
27144706
Design
Generation 4
Note
A protective cap is supplied as standard for the DC and AC contacts.
Conductor length
2 m (AC cables)
Type of charging current
DC, AC 3-phase
Number of phases
3
Number of power contacts
7 (L1, L2, L3, N, PE, DC+, DC-)
Insertion force
< 100 N
Mounting position of the locking actuator
Right-side
Locking type
Locking in the inserted state with a locking mechanism
Material surface of contacts
Ag
Minimum bending radius
15 mm
Reverse current of the motor
max. 0.5 A
Typical motor current for locking
0.05 A
Type of sensor
Pt 1000
ECLASS 11.0
27144706
Cable weight
7 kg/km
Customer variations
On request
Flammability rating
V0
Type
Locking actuator right
Charging standard
CCS type 2
Width
108 mm
Ambient temperature (operation)
-30 °C ... 50 °C
Rated current of power contacts
32 A AC
Insulation resistance of neighboring contacts
> 200 MΩ
Withdrawal force
< 100 N
Design line
Generation 4
Single wire, color
black PP/CS
Operating voltage
24 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Cable length
0.5 m
Mechanical emergency release
available
Resistance range
650 Ω ... 1450 Ω
Recommended adaptation time
600 ms
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Temperature range
-40 °C ... 130 °C
ECLASS 10.0.1
27144706