2903144 Phoenix Contact AC/DC Power Supplies

Product Details

• UNSPSC 11
  39121004
• Width
  35 mm
• Ambient temperature (start-up type tested)
  -25 °C
• Nominal input voltage range
  100 V AC ... 240 V AC
• Current consumption
  2.2 A (100 V AC)
• Recommended breaker for input protection
  6 A ... 16 A (Characteristics B, C, D, K)
• Power factor (cos phi)
  0.5
• Connection in series
  yes
• Typical response time
  < 1 s
• Net weight
  0.45 kg
• Assembly instructions
  alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
• Conductor cross section flexible min.
  0.2 mm²
• Stripping length
  8 mm
• Standard - Electrical safety
  IEC 60950-1/VDE 0805 (SELV)
• Standard – Limitation of mains harmonic currents
  EN 61000-3-2
• Contact discharge
  6 kV (Test Level 4)
• Input
  2 kV (Test Level 3 - symmetrical)
• Conducted interference
  EN 61000-4-6
• REACh SVHC
  Lead 7439-92-1
• ECLASS 5.1
  27049000
ETIM 7.0
EC002540
UNSPSC 21.0
39121004
Installation distance top/bottom
50 mm / 50 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
AC frequency range
50 Hz ... 60 Hz ±5 Hz
Frequency range (fN)
50 Hz ... 60 Hz ±10 %
Type of protection
Transient surge protection
Setting range of the output voltage (USet)
24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
Feedback voltage resistance
≤ 35 V DC
Output power
120 W
Protection class
II (in closed control cabinet)
Conductor cross section solid max.
1.5 mm²
EMC requirements for noise immunity
EN 61000-6-1
Rail applications
EN 50121-4
Discharge in air
8 kV (Test Level 4)
Comments
Criterion A
Surge voltage load (surge)
EN 61000-4-5
Voltage
10 V (Test Level 3)
ECLASS 10.0.1
27040701
ETIM 4.0
EC000599
UNSPSC 6.01
30211502
UNSPSC 20.0
39121004
Installation distance right/left
0 mm / 0 mm
Degree of protection
IP20
Dielectric strength maximum
≤ 300 V AC 15 s
Discharge current to PE
< 0.25 mA
Mains buffering time
typ. 20 ms (120 V AC)
Protective circuit/component
Varistor
Dynamic Boost (IDyn.Boost)
7.5 A (5 s)
Protection against overvoltage at the output (OVP)
≤ 30 V DC
Efficiency
> 89 % (for 230 V AC and nominal values)
Insulation voltage input/output
3 kV AC (type test)
Conductor cross section flexible max.
1.5 mm²
Standard – Safety extra-low voltage
IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Shipbuilding approval
DNV GL (EMC B)
Electromagnetic HF field
EN 61000-4-3
Output
1 kV (Test Level 2 - symmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 5.0
27049000
ETIM 3.0
EC001039
UNSPSC 13.2
39121004
Height
130 mm
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Degree of pollution
2
Nominal power consumption
272 VA
Input fuse
6.3 A (internal (device protection))
Nominal output voltage
24 V DC ±1 %
Derating
> 60 °C ... 70 °C (2.5%/K)
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Maximum power dissipation in no-load condition
< 1 W
Power loss nominal load max.
< 16 W
Mounting position
horizontal DIN rail NS 35, EN 60715
Connection method
Push-in connection
Conductor cross section AWG max.
16
EMC requirements for noise emission
EN 61000-6-3
Standard - Safe isolation
DIN VDE 0100-410
UL approvals
UL Listed UL 508
Electrostatic discharge
EN 61000-4-2
Fast transients (burst)
EN 61000-4-4
Signal
1 kV (Test Level 2 - asymmetrical)
ECLASS 11.0
27040701
ECLASS 4.0
27040700
ECLASS 9.0
27040701
ETIM 6.0
EC002540
UNSPSC 18.0
39121004
Depth
115 mm
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Climatic class
3K3 (in acc. with EN 60721)
Installation height
≤ 5000 m (> 2000 m, observe derating)
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Inrush current
≤ 16 A (typical)
Nominal output current (IN)
5 A
Connection in parallel
Yes, for redundancy and increased capacity
Residual ripple
< 50 mVPP (with nominal values)
MTBF (IEC 61709, SN 29500)
> 3380000 h (25 °C)
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG min.
24
Standard - Safety of transformers
EN 61558-2-16 (air clearances and creepage distances only)
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Mains variation/undervoltage
Semi F47-0706
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Test field strength
10 V/m (Test Level 3)
Frequency range
0.15 MHz ... 80 MHz
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 4.1
27040700
ECLASS 7.0
27049002
ECLASS 6.0
27049000
UNSPSC 7.0901
39121004
UNSPSC 12.01
39121004
UNSPSC 19.0
39121004