2903156 Phoenix Contact AC/DC Power Supplies

Product Details

• Width
  110 mm
• Height
  130 mm
• Depth
  160 mm
• Installation distance right/left
  0 mm / 0 mm
• Installation distance top/bottom
  50 mm / 50 mm
• Degree of protection
  IP20
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Climatic class
  3K3 (in acc. with EN 60721)
• Degree of pollution
  2
• Input voltage range
  3x 400 V AC ... 500 V AC -20 % ....+15 %
• Nominal input voltage range
  3x 400 V AC ... 500 V AC
• Nominal power consumption
  1335.1 VA
• Mains buffering time
  > 10 ms (400 V AC)
• Type of protection
  Transient surge protection
• Nominal output voltage
  24 V DC ±1 %
• Signal
  1 kV (Test Level 2 - asymmetrical)
• Voltage
  230 V AC
• Criterion B
  Temporary impairment to operational behavior that is corrected by the device itself.
• REACh SVHC
  Lead 7439-92-1
ECLASS 6.0
27049000
ECLASS 9.0
27040701
UNSPSC 20.0
39121004
Current consumption
3x 1.9 A (400 V AC)
Input fuse
6.3 A (internal (device protection))
Nominal output current (IN)
40 A
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Output power
960 W
Typical response time
< 1 s
Protection class
I (in closed control cabinet)
Insulation voltage input/output
3 kV AC (type test)
Connection method
Push-in connection
EMC requirements for noise immunity
EN 61000-6-1
Standard - Safety of power supply units up to 1100 V (insulation distances)
DIN EN 61558-2-16
Standard - Safe isolation
DIN VDE 0100-410
Power factor (cos phi)
0.77
Protective circuit/component
Varistor
Feedback voltage resistance
< 35 V
Residual ripple
≤ 50 mVPP
Power loss nominal load max.
< 70 W (480 V AC)
MTBF (IEC 61709, SN 29500)
> 1730000 h (25 °C)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section flexible min.
0.2 mm²
Conductor cross section AWG max.
16
Standard – Safety extra-low voltage
IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Noise emission
EN 55016
Electrostatic discharge
EN 61000-4-2
Fast transients (burst)
EN 61000-4-4
Input
3 kV (Test Level 4 - symmetrical)
Surge voltage load (surge)
EN 61000-4-5
Criterion A
Normal operating behavior within the specified limits.
ECLASS 11.0
27040701
ECLASS 7.0
27049002
ETIM 6.0
EC002540
UNSPSC 18.0
39121004
Ambient temperature (start-up type tested)
-40 °C
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Installation height
≤ 4000 m (> 2000 m, Derating: 10 %/1000 m)
AC frequency range
50 Hz ... 60 Hz
Frequency range (fN)
50 Hz ... 60 Hz ±5 Hz
Discharge current to PE
< 3.5 mA
Recommended breaker for input protection
10 A ... 16 A (Characteristics B, C, D, K)
Setting range of the output voltage (USet)
24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
Connection in parallel
Yes, for redundancy and increased capacity
Connection in series
yes
Protection against overvoltage at the output (OVP)
≤ 30 V DC
Short-circuit current
< 48 A DC (Permanent)
Efficiency
typ. 93 % (400 V AC)
Assembly instructions
alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
Conductor cross section solid max.
1.5 mm²
Conductor cross section AWG min.
24
EMC requirements for noise emission
EN 61000-6-3
Rail applications
EN 50121-4
UL approvals
UL Listed UL 508
Discharge in air
8 kV (Test Level 3)
Frequency range
0.15 MHz ... 80 MHz
Comments
Criterion A
Frequency
50 Hz
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 5.0
27049000
ETIM 7.0
EC002540
UNSPSC 19.0
39121004
Dynamic Boost (IDyn.Boost)
60 A (5 s)
Derating
> 60 °C ... 70 °C (2.5%/K)
Maximum power dissipation in no-load condition
typ. 14 W (400 V AC)
Net weight
2.6 kg
Conductor cross section solid min.
0.2 mm²
Conductor cross section flexible max.
1.5 mm²
Stripping length
8 mm
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Contact discharge
6 kV (Test Level 3)
Test field strength
10 V/m (Test Level 3)
Output
1 kV (Test Level 3 - symmetrical)
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.
ECLASS 10.0.1
27040701
ECLASS 4.1
27040700
ETIM 4.0
EC002540
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Conducted noise emission
EN 55016
Electromagnetic HF field
EN 61000-4-3
Conducted interference
EN 61000-4-6
Voltage dips
EN 61000-4-11
ECLASS 4.0
27040700
ECLASS 5.1
27049000
UNSPSC 13.2
39121004
UNSPSC 21.0
39121004