3002371 Phoenix Contact Terminal Blocks

Product Details

• Result of thermal test
  Test passed
• Shock test result
  Test passed
• Shock form
  Half-sine
• Specific optical density of smoke NFPA 130 (ASTM E 662)
  passed
• Fire protection for rail vehicles (DIN EN 45545-2) R22
  HL 1 - HL 3
• Conductor cross section flexible max.
  10 mm²
• 2 conductors with same cross section, solid min.
  1.5 mm²
• Open side panel
  No
• Result of power-frequency withstand voltage test
  Test passed
• Bending test turns
  135
• Tractive force setpoint
  190 N
• Result of temperature-rise test
  Test passed
• Short-time current
  4.2 kA
• 2 conductors with same cross section, solid max.
  16 mm²
• 2 conductors with same cross section, stranded max.
  10 mm²
• ECLASS 10.0.1
  27141120
• Permissible humidity (storage/transport)
  30 % ... 70 %
• ECLASS 5.1
  27141111
• ETIM 3.0
  EC000897
• UNSPSC 7.0901
  39121410
Conductor cross section short circuit testing
35 mm²
Proof of thermal characteristics (needle flame) effective duration
30 s
Number of shocks per direction
3
Surface flammability NFPA 130 (ASTM E 162)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Width
19.4 mm
Tightening torque, min
3.2 Nm
Degree of pollution
2
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Tensile test result
Test passed
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible min.
0.5 mm²
2 conductors with same cross section, stranded min.
1.5 mm²
Two conductors with the same cross section, AWG stranded, max.
8
Internal cylindrical gage
B9
Ambient temperature (actuation)
-5 °C ... 70 °C
Tight fit on carrier
NS 35
Requirements, voltage drop
≤ 1.6 mV
Short circuit stability result
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Connection method
Push-in connection
Maximum load current
57 A
Result of surge voltage test
Test passed
Bending test conductor cross section/weight
2.5 mm² / 0.7 kg
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Conductor cross section AWG min.
20
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, AWG solid max.
6
ECLASS 5.0
27141127
Result of voltage-drop test
Test passed
Ageing test for screwless modular terminal block temperature cycles
192
Test spectrum
Service life test category 2, bogie-mounted
Maximum power dissipation for nominal condition
4.06 W (the value is multiplied when connecting multiple levels)
Finger protection
guaranteed
Power frequency withstand voltage setpoint
2.2 kV
Conductor cross section tensile test
35 mm²
Result of tight fit on support
Test passed
Acceleration
30g
Shock duration
18 ms
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Height NS 35/15
57.8 mm
Conductor cross section AWG max.
6
Conductor cross section solid min.
0.5 mm²
ECLASS 4.0
27141127
Conductor cross section solid max.
16 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
10 mm²
Surge voltage test setpoint
9.8 kV
Bending test rotation speed
10 rpm
Setpoint
5 N
Result of aging test
Test passed
Oscillation, broadband noise test result
Test passed
Test duration per axis
5 h
Static insulating material application in cold
-60 °C
Two conductors with the same cross section, AWG solid min.
16
Nominal current IN
57 A
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Height NS 35/7,5
50.3 mm
Tightening torque max
3.7 Nm
Connection cross sections directly pluggable
1 mm² 16 mm² 16 6 4 mm² 10 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 4.1
27141127
ECLASS 6.0
27141100
UNSPSC 6.01
30211812
Connection in acc. with standard
IEC 60947-7-1
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Note
In the end application, the applicable safety regulations for overload and short-circuit protection on the connected conductors must be considered.
Insulating material group
I
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Conductor cross section flexible, with ferrule with plastic sleeve max.
10 mm²
Nominal cross section
16 mm²
Rated surge voltage
8 kV
Nominal voltage UN
1000 V
Result of flexion and pull-out test
Test passed
Number of levels
1
Overvoltage category
III
Length
79.9 mm
Flammability rating according to UL 94
V0
ASD level
6.12 (m/s2)2/Hz
Stripping length
18 mm
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Screw thread
M6
Max. AWG conductor cross section, flexible
8
Two conductors with the same cross section, AWG stranded, min.
16
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 7.0
27141120
ETIM 6.0
EC000897
Back of the hand protection
guaranteed
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
10 mm²
ECLASS 9.0
27141120
ETIM 7.0
EC000897
UNSPSC 11
39121411
Insulating material
PA
UNSPSC 19.0
39121410
Color
gray
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
1.5 mm²
UNSPSC 12.01
39121411
Number of connections
5
ECLASS 11.0
27141120
ETIM 4.0
EC000897
UNSPSC 20.0
39121410
UNSPSC 21.0
39121410
UNSPSC 13.2
39121411
UNSPSC 18.0
39121410