1088851 Phoenix Contact AC/DC Power Supplies

Product Details

• Width
  55 mm
• Depth
  84 mm
• Installation distance top/bottom
  30 mm / 30 mm
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Ambient temperature (start-up type tested)
  -40 °C
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Degree of pollution
  2
• Frequency range (fN)
  50 Hz ... 60 Hz 10 %
• Current consumption
  2.1 A (100 V AC)
• Inrush current
  < 40 A (typical)
• Input fuse
  4 A (slow-blow, internal)
• Type of protection
  Transient surge protection
• Nominal output voltage
  24 V DC ±1 %
• Height
  90 mm
• Installation distance right/left
  0 mm / 0 mm
• Degree of protection
  IP20
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Protective circuit/component
  Varistor
• Power factor (cos phi)
  0.47
• Feedback voltage resistance
  < 35 V DC
Nominal output current (IN)
4.2 A (-25 °C ... 55 °C)
Residual ripple
< 30 mVPP (with nominal values)
Power loss nominal load max.
< 11 W
MTBF (IEC 61709, SN 29500)
> 738000 h (40 °C)
Protection class
II (in closed control cabinet)
Foot latch material
POM (Polyoxymethylen)
Conductor cross section solid max.
2.5 mm²
Conductor cross section AWG min.
24
EMC requirements for noise immunity
EN 61000-6-1
Stripping length
8 mm
Standard - Electrical safety
IEC 62368-1/VDE 0805 (SELV)
Standard – Safety extra-low voltage
IEC 62368-1 (SELV) und EN 60204-1 (PELV)
UL approvals
UL/C-UL listed UL 508
Criterion A
Normal operating behavior within the specified limits.
Derating
55 °C ... 70 °C (2.5%/K)
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Typical response time
< 1 s
Efficiency
typ. 88 % (120 V AC)
Insulation voltage input/output
4 kV AC (type test)
Assembly instructions
alignable: 0 mm horizontally, 30 mm vertically
Conductor cross section solid min.
0.2 mm²
Conductor cross section flexible min.
0.2 mm²
Screw thread
M3
EMC requirements for noise emission
EN 61000-6-3
Standard - Safety of transformers
EN 61558-2-16
Standard - Safe isolation
DIN VDE 0100-410
Mains variation/undervoltage
EN 61000-4-11
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Contact discharge
6 kV (Test Level 3)
Comments
Criterion A
Connection in series
yes
Protection against overvoltage at the output (OVP)
≤ 35 V DC
Output power
100 W
Maximum power dissipation in no-load condition
< 0.5 W
Net weight
0.34 kg
Housing material
Polycarbonate
Mounting position
horizontal DIN rail NS 35, EN 60715
Connection method
Screw connection
Conductor cross section flexible max.
2.5 mm²
Ambient temperature (operation)
-25 °C ... 70 °C (> 55 °C Derating: 2.5 %/K)
Nominal input voltage range
100 V AC ... 240 V AC
Mains buffering time
> 20 ms (120 V AC)
Recommended breaker for input protection
6 A ... 16 A (Characteristics B, C, D, K)
CSA
CAN/CSA-C22.2 No. 60950-1-07
Electrostatic discharge
EN 61000-4-2
Output
1 kV (Test Level 2 - symmetrical)
ECLASS 10.0.1
27040701
Nominal power consumption
242.6 VA
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Discharge in air
8 kV (Test Level 3)
Test field strength
10 V/m
Input
2 kV (Test Level 3 - symmetrical)
Conducted interference
EN 61000-4-6
ECLASS 9.0
27040701
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
85 V AC ... 264 V AC
Conductor cross section AWG max.
14
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Frequency range
150 kHz ... 80 MHz
Voltage
10 V (Test Level 3)
REACh SVHC
Lead 7439-92-1
ECLASS 11.0
27040701
Voltage dips
EN 61000-4-11
Budgetary standard
IEC 60335-1
Electromagnetic HF field
EN 61000-4-3
Fast transients (burst)
EN 61000-4-4
Surge voltage load (surge)
EN 61000-4-5
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.