2866695 Phoenix Contact AC/DC Power Supplies

Product Details

• Height
  130 mm
• Depth with alternative assembly
  183 mm
• Degree of protection
  IP20
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Nominal input voltage range
  100 V AC ... 240 V AC
• AC frequency range
  45 Hz ... 65 Hz
• Input fuse
  20 A (fast blow, internal)
• Nominal output voltage
  48 V DC ±1 %
• Nominal output current (IN)
  20 A (-25 °C ... 60 °C, UOUT = 48 V DC)
• Derating
  60 °C ... 70 °C (2.5%/K)
• Residual ripple
  < 50 mVPP (with nominal values)
• Efficiency
  > 93 % (for 230 V AC and nominal values)
• Connection method
  Screw connection
• Conductor cross section AWG min.
  24
• EMC requirements for noise immunity
  EN 61000-6-1
• Standard – Limitation of mains harmonic currents
  EN 61000-3-2
• SIQ
  BG (type approved)
• Contact discharge
  8 kV (Test Level 4)
• Test field strength
  10 V/m (Test Level 3)
• Signal
  1 kV (Test Level 2 - asymmetrical)
Conducted interference
EN 61000-4-6
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 5.0
27242200
ETIM 4.0
EC002540
ETIM 7.0
EC002540
UNSPSC 12.01
39121004
UNSPSC 18.0
39121004
Depth
125 mm
Installation distance right/left
5 mm / 5 mm
Ambient temperature (start-up type tested)
-40 °C
Degree of pollution
2
Dielectric strength maximum
300 V AC
Frequency range DC
0 Hz
Nominal power consumption
1046 VA
Type of protection
Transient surge protection
Setting range of the output voltage (USet)
30 V DC ... 56 V DC (> 48 V DC, constant capacity restricted)
Connection in series
yes
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Power loss nominal load max.
74 W
Insulation voltage input / PE
3.5 kV AC (type test)
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Conductor cross section flexible min.
0.2 mm²
Conductor cross section AWG max.
10
Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment
EN 50178
CSA
CAN/CSA-C22.2 No. 60950-1-07
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electromagnetic HF field
EN 61000-4-3
Surge voltage load (surge)
EN 61000-4-5
Criterion A
Normal operating behavior within the specified limits.
ECLASS 10.0.1
27040701
ECLASS 4.1
27040700
ECLASS 6.0
27049000
ECLASS 9.0
27040701
UNSPSC 13.2
39121004
Width with alternative assembly
122 mm
Width
180 mm
Height with alternative assembly
130 mm
Installation distance top/bottom
50 mm / 50 mm
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Installation height
6000 m
Current consumption
8.7 A (120 V AC)
Inrush current
< 15 A (typical)
Recommended breaker for input protection
6 A ... 16 A (AC: Characteristics B, C, D, K)
POWER BOOST (IBoost)
22.5 A (-25 °C ... 40 °C permanent, UOUT = 48 V DC )
Connection in parallel
Yes, for redundancy and increased capacity
Active current limitation
Approx. IBOOST = 22.5 A (for short-circuit)
Protection against overvoltage at the output (OVP)
< 60 V DC
Typical response time
< 0.65 s
Insulation voltage output / PE
500 V DC (routine test)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section flexible max.
4 mm²
EMC requirements for noise emission
EN 61000-6-3
Standard – Safety extra-low voltage
IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Rail applications
EN 50121-4
Shipbuilding approval
DNV GL (EMC A)
Discharge in air
15 kV (Test Level 4)
Fast transients (burst)
EN 61000-4-4
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 7.0
27049002
UNSPSC 11
39121004
UNSPSC 21.0
39121004
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
85 V AC ... 264 V AC
Discharge current to PE
< 3.5 mA
Mains buffering time
typ. 20 ms (120 V AC)
Protective circuit/component
Varistor
Selective Fuse Breaking (ISFB)
100 A (12 ms)
Feedback voltage resistance
max. 60 V DC
Maximum power dissipation in no-load condition
12 W
Insulation voltage input/output
4 kV AC (type test)
Conductor cross section solid max.
6 mm²
Stripping length
10 mm
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Standard - Safe isolation
DIN VDE 0100-410
Standard - Equipment safety
BG (design tested)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Comments
Criterion A
Input
2 kV (Test Level 3 - symmetrical)
I/O/S
asymmetrical
ECLASS 4.0
27040700
ECLASS 5.1
27242200
UNSPSC 6.01
30211502
UNSPSC 20.0
39121004
Output power
960 W
Net weight
3.3 kg
MTBF (IEC 61709, SN 29500)
> 880000 h (25 °C)
Protection class
I
Conductor cross section solid min.
0.2 mm²
Screw thread
M3
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
UL approvals
UL Listed UL 508
Electrostatic discharge
EN 61000-4-2
Frequency range
0.15 MHz ... 80 MHz
Output
1 kV (Test Level 2 - symmetrical)
Voltage
10 V (Test Level 3)
REACh SVHC
Lead 7439-92-1
ECLASS 11.0
27040701
ETIM 3.0
EC001039
ETIM 6.0
EC002540
UNSPSC 7.0901
39121004
UNSPSC 19.0
39121004