2320131 Phoenix Contact DC/DC Converters

Product Details

• Height with alternative assembly
  130 mm
• Degree of protection
  IP20
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Mains buffering time
  typ. 3 ms (12 V DC)
• Protective circuit/component
  Varistor
• POWER BOOST (IBoost)
  6.25 A (-25 °C ... 40 °C permanent, UOUT = 24 V DC )
• Max. capacitive load
  unlimited
• MTBF (IEC 61709, SN 29500)
  > 1005000 h (40 °C)
• Assembly instructions
  alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
• Conductor cross section flexible max.
  2.5 mm²
• Depth
  125 mm
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Type of protection
  Transient surge protection
• Nominal output current (IN)
  5 A (-25 °C ... 60 °C)
• Connection in parallel
  Yes, for redundancy and increased capacity
• Maximum power dissipation in no-load condition
  2 W
• Power loss nominal load max.
  13.5 W
• Mounting position
  horizontal DIN rail NS 35, EN 60715
• Conductor cross section flexible min.
  0.2 mm²
Stripping length
7 mm
EMC requirements for noise emission
EN 61000-6-3
UL approvals
UL/C-UL listed UL 508
Contact discharge
8 kV (Test Level 4)
Comments
Criterion A
Signal
1 kV (Test Level 2 - asymmetrical)
Surge voltage load (surge)
EN 61000-4-5
ECLASS 4.1
27210900
ECLASS 4.0
27210900
ECLASS 7.0
27210901
UNSPSC 12.01
39121004
UNSPSC 20.0
39121041
Width
32 mm
Depth with alternative assembly
35 mm
Ambient temperature (start-up type tested)
-40 °C
Input voltage range
9 V DC ... 18 V DC
Climatic class
3K3 (in acc. with EN 60721)
Nominal output voltage
24 V DC ±1 %
Derating
60 °C ... 70 °C (2.5%/K)
Protection against overvoltage at the output (OVP)
< 35 V DC
Active current limitation
Approximately 6.9 A
Residual ripple
< 75 mVPP
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG max.
12
Rail applications
EN 50121-4
Electrostatic discharge
EN 61000-4-2
Input
1 kV (Test Level 2 - symmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 10.0.1
27210901
ECLASS 9.0
27210901
ETIM 7.0
EC002046
UNSPSC 13.2
39121041
UNSPSC 11
39121004
Width with alternative assembly
122 mm
Installation distance right/left (active)
15 mm / 15 mm (≤ 70 °C)
Installation distance top/bottom (active)
50 mm / 50 mm (≤ 70 °C)
Current consumption
15 A (12 V, IBOOST)
Input fuse
25 A (internal (device protection))
Setting range of the output voltage (USet)
18 V DC ... 29.5 V DC (> 24 V DC, constant capacity restricted)
Connection in series
yes
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Efficiency
> 90 %
Insulation voltage input/output
1.5 kV (type test)
Connection method
Screw connection
Screw thread
M3
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electromagnetic HF field
EN 61000-4-3
I/O/S
asymmetrical
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ETIM 4.0
EC002540
ECLASS 5.1
27210900
UNSPSC 7.0901
39121004
UNSPSC 21.0
39121041
Height
130 mm
Installation distance right/left
0 mm / 0 mm (≤ 70 °C)
Installation distance top/bottom
50 mm / 50 mm (≤ 70 °C)
Degree of pollution
2
Nominal input voltage range
12 V DC
Inrush current
< 15 A (typical)
Selective Fuse Breaking (ISFB)
30 A (12 ms)
Feedback voltage resistance
35 V DC
Peak switching voltages nominal load
< 10 mVPP (20 MHz)
Net weight
0.7 kg
Protection class
III
Conductor cross section solid max.
2.5 mm²
Conductor cross section AWG min.
24
EMC requirements for noise immunity
EN 61000-6-1
Standard - Safe isolation
DIN VDE 0100-410
Standard – Safety extra-low voltage
EN 60950-1 (SELV)
Test field strength
10 V/m (Test Level 3)
Fast transients (burst)
EN 61000-4-4
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 5.0
27210900
ETIM 6.0
EC002046
UNSPSC 18.0
39121041
Standard - Electrical safety
EN 60950-1/VDE 0805 (SELV)
Discharge in air
15 kV (Test Level 4)
Frequency range
0.15 MHz ... 80 MHz
Output
1 kV (Test Level 2 - symmetrical)
Voltage
10 V (Test Level 3)
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 11.0
27210901
ECLASS 6.0
27210900
UNSPSC 6.01
30211502
UNSPSC 19.0
39121041