2902993 Phoenix Contact AC/DC Power Supplies

Product Details

• Current consumption
  2.1 A (100 V AC)
• ECLASS 11.0
  27040701
• ECLASS 4.1
  27040700
• ECLASS 5.1
  27049000
• UNSPSC 13.2
  39121004
• UNSPSC 11
  39121004
• UNSPSC 21.0
  39121004
• Installation distance right/left
  0 mm / 0 mm
• Test field strength
  10 V/m
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Input voltage range
  85 V AC ... 264 V AC
• Power factor (cos phi)
  0.47
• Derating
  55 °C ... 70 °C (2.5%/K)
• Feedback voltage resistance
  < 35 V DC
• Output power
  100 W
• Protection class
  II (in closed control cabinet)
• Mounting position
  horizontal DIN rail NS 35, EN 60715
• Screw thread
  M3
• EMC requirements for noise immunity
  EN 61000-6-1
• Standard – Safety extra-low voltage
  IEC 62368-1 (SELV) und EN 60204-1 (PELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Surge voltage load (surge)
EN 61000-4-5
Criterion A
Normal operating behavior within the specified limits.
ECLASS 9.0
27040701
UNSPSC 7.0901
39121004
Height
90 mm
Installation distance top/bottom
30 mm / 30 mm
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Frequency range (fN)
50 Hz ... 60 Hz 10 %
Nominal power consumption
242.6 VA
Input fuse
4 A (slow-blow, internal)
Nominal output voltage
24 V DC ±1 %
Connection in parallel
Yes, for redundancy and increased capacity
Maximum power dissipation in no-load condition
< 0.5 W
Efficiency
typ. 88 % (120 V AC)
MTBF (IEC 61709, SN 29500)
> 738000 h (40 °C)
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG max.
14
Standard - Safety of transformers
EN 61558-2-16
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Mains variation/undervoltage
EN 61000-4-11
Electrostatic discharge
EN 61000-4-2
Fast transients (burst)
EN 61000-4-4
Input
2 kV (Test Level 3 - symmetrical)
Voltage dips
EN 61000-4-11
ECLASS 10.0.1
27040701
ETIM 4.0
EC000599
UNSPSC 6.01
30211502
Width
55 mm
Degree of protection
IP20
Degree of pollution
2
Recommended breaker for input protection
6 A ... 16 A (Characteristics B, C, D, K)
Type of protection
Transient surge protection
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Power loss nominal load max.
< 11 W
Foot latch material
POM (Polyoxymethylen)
Connection method
Screw connection
Conductor cross section flexible max.
2.5 mm²
Standard - Electrical safety
IEC 62368-1/VDE 0805 (SELV)
Standard - Safe isolation
DIN VDE 0100-410
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Discharge in air
8 kV (Test Level 3)
Comments
Criterion A
Voltage
10 V (Test Level 3)
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 5.0
27049000
ETIM 7.0
EC002540
UNSPSC 19.0
39121004
UNSPSC 20.0
39121004
Depth
84 mm
Ambient temperature (start-up type tested)
-40 °C
Climatic class
3K3 (in acc. with EN 60721)
Inrush current
< 40 A (typical)
Nominal output current (IN)
4.2 A (-25 °C ... 55 °C)
Protection against overvoltage at the output (OVP)
≤ 35 V DC
Typical response time
< 1 s
Insulation voltage input/output
4 kV AC (type test)
Assembly instructions
alignable: 0 mm horizontally, 30 mm vertically
Conductor cross section flexible min.
0.2 mm²
EMC requirements for noise emission
EN 61000-6-3
CSA
CAN/CSA-C22.2 No. 60950-1-07
Contact discharge
6 kV (Test Level 3)
Output
1 kV (Test Level 2 - symmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 4.0
27040700
ECLASS 6.0
27049000
ETIM 3.0
EC001039
UNSPSC 12.01
39121004
UNSPSC 18.0
39121004
Ambient temperature (operation)
-25 °C ... 70 °C (> 55 °C Derating: 2.5 %/K)
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Nominal input voltage range
100 V AC ... 240 V AC
Mains buffering time
> 20 ms (120 V AC)
Protective circuit/component
Varistor
Connection in series
yes
Residual ripple
< 30 mVPP (with nominal values)
Net weight
0.34 kg
Housing material
Polycarbonate
Conductor cross section solid max.
2.5 mm²
Conductor cross section AWG min.
24
Stripping length
8 mm
UL approvals
UL/C-UL listed UL 508
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Frequency range
150 kHz ... 80 MHz
Electromagnetic HF field
EN 61000-4-3
Conducted interference
EN 61000-4-6
ECLASS 7.0
27049002
ETIM 6.0
EC002540