2902999 Phoenix Contact AC/DC Power Supplies

Product Details

• Mains buffering time
  > 20 ms (120 V AC)
• Protective circuit/component
  Varistor
• Protection against overvoltage at the output (OVP)
  ≤ 25 V DC
• Connection in parallel
  Yes, for redundancy and increased capacity
• Net weight
  0.2 kg
• ECLASS 5.0
  27049000
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 55 °C Derating: 2.5 %/K)
• Climatic class
  3K3 (in acc. with EN 60721)
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Degree of protection
  IP20
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Nominal input voltage range
  100 V AC ... 240 V AC
• Inrush current
  < 30 A (typical)
• Nominal output voltage
  12 V DC ±1 %
• Connection in series
  yes
• Control deviation
  < 1 % (change in load, static 10 % ... 90 %)
• MTBF (IEC 61709, SN 29500)
  > 865000 h (40 °C)
• Housing material
  Polycarbonate
• Conductor cross section solid min.
  0.2 mm²
• Stripping length
  8 mm
Standard - Electrical safety
IEC 62368-1/VDE 0805 (SELV)
Mains variation/undervoltage
EN 61000-4-11
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Degree of pollution
2
Frequency range (fN)
50 Hz ... 60 Hz 10 %
Nominal power consumption
127 VA
Power factor (cos phi)
0.49
Feedback voltage resistance
< 25 V DC
Power loss nominal load max.
< 8 W
Protection class
II (in closed control cabinet)
Assembly instructions
alignable: 0 mm horizontally, 30 mm vertically
Conductor cross section flexible max.
2.5 mm²
Screw thread
M3
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Contact discharge
6 kV (Test Level 3)
Comments
Criterion A
Surge voltage load (surge)
EN 61000-4-5
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 4.0
27040700
Input voltage range
85 V AC ... 264 V AC
Current consumption
1.3 A (100 V AC)
Type of protection
Transient surge protection
Input fuse
2 A (slow-blow, internal)
Test field strength
10 V/m
AC frequency range
50 Hz ... 60 Hz -10 % ... +10 %
Recommended breaker for input protection
6 A ... 16 A (Characteristics B, C, D, K)
Nominal output current (IN)
4.6 A (-25 °C ... 55 °C)
Residual ripple
< 30 mVPP (with nominal values)
Output power
55 W
Conductor cross section flexible min.
0.2 mm²
Foot latch material
POM (Polyoxymethylen)
EMC requirements for noise immunity
EN 61000-6-1
Standard – Safety extra-low voltage
IEC 62368-1 (SELV) und EN 60204-1 (PELV)
UL approvals
UL/C-UL listed UL 508
Discharge in air
8 kV (Test Level 3)
Output
1 kV (Test Level 2 - symmetrical)
Voltage
10 V (Test Level 3)
ECLASS 10.0.1
27040701
ECLASS 5.1
27049000
Width
35 mm
Installation distance right/left
0 mm / 0 mm
Typical response time
< 1 s
Standard - Safe isolation
DIN VDE 0100-410
Electromagnetic HF field
EN 61000-4-3
Frequency range
150 kHz ... 80 MHz
Voltage dips
EN 61000-4-11
China RoHS
Environmentally Friendly Use Period = 25;
Criterion A
Normal operating behavior within the specified limits.
ECLASS 7.0
27049002
ETIM 6.0
EC002540
ETIM 3.0
EC001039
Depth
84 mm
Installation distance top/bottom
30 mm / 30 mm
Maximum power dissipation in no-load condition
< 0.3 W
Connection method
Screw connection
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Fast transients (burst)
EN 61000-4-4
Conducted interference
EN 61000-4-6
ECLASS 6.0
27049000
ETIM 7.0
EC002540
UNSPSC 6.01
30211502
UNSPSC 12.01
39121004
UNSPSC 21.0
39121004
Ambient temperature (start-up type tested)
-25 °C
Derating
55 °C ... 70 °C (2.5%/K)
Conductor cross section solid max.
2.5 mm²
EMC requirements for noise emission
EN 61000-6-3
Standard - Safety of transformers
EN 61558-2-16
CSA
CAN/CSA-C22.2 No. 60950-1-07
Electrostatic discharge
EN 61000-4-2
ECLASS 9.0
27040701
UNSPSC 11
39121004
UNSPSC 19.0
39121004
UNSPSC 18.0
39121004
Height
90 mm
Efficiency
typ. 87 % (120 V AC)
Insulation voltage input/output
4 kV AC (type test)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section AWG max.
14
Conductor cross section AWG min.
24
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Input
2 kV (Test Level 3 - symmetrical)
ECLASS 11.0
27040701
ECLASS 4.1
27040700
ETIM 4.0
EC000599
UNSPSC 7.0901
39121004
UNSPSC 13.2
39121004
UNSPSC 20.0
39121004