X20AIA744 B&R Electronic Components

Product Details

• Temperature Operation Horizontal mounting orientation
  -25 to 60°C
• Temperature Operation Vertical mounting orientation
  -25 to 50°C
• Quantization LSB value 256 mV/V
  167.85 nV
• Quantization LSB value 64 mV/V
  41.96 nV
• Quantization LSB value 16 mV/V
  10.49 nV
• Quantization LSB value 128 mV/V
  83.92 nV
• Quantization LSB value 32 mV/V
  20.98 nV
• Quantization LSB value 2 mV/V
  1.31 nV
• Quantization LSB value 8 mV/V
  5.25 nV
• Relative humidity Transport
  5 to 95%, non-condensing
• Quantization LSB value 4 mV/V
  2.62 nV
• Relative humidity Storage
  5 to 95%, non-condensing
• Relative humidity Operation
  5 to 95%, non-condensing
• Temperature Transport
  -40 to 85°C
• Temperature Derating
  See section "Hardware configuration"
• Temperature Storage
  -40 to 85°C
• Installation elevation above sea level 0 to 2000 m
  No limitation
• Installation elevation above sea level >2000 m
  Reduction of ambient temperature by 0.5°C per 100 m
• Mounting orientation Vertical
  Yes
• Mounting orientation Horizontal
  Yes
Strain gauge supply Voltage
5.5 VDC / Max. 65 mA per channel
Strain gauge supply Short-circuit and overload-proof
Yes
Output of digital value Broken sensor line
Value approaching ±end value (status bit "Open circuit" set in register "Module status")
Output of digital value Valid range of values
0xFF800001 to 0x007FFFFF (-8,388,607 to 8,388,607)
Output of digital value Broken bridge supply line
Value approaching 0
Input filter Slope
60 dB
Certifications UL
cULus E115267; Industrial control equipment
Input filter Order
3
Input filter Cutoff frequency
2.5 kHz
Certifications EAC
Yes
Certifications ATEX
Zone 2, II 3G Ex nA nC IIA T5 Gc; IP20, Ta (see X20 user's manual); FTZÚ 09 ATEX 0083X
Certifications CE
Yes
Certifications UKCA
Yes
Power consumption Bus
0.01 W
Diagnostics Input
Yes, using LED status indicator and software
Note
Order 1x terminal block X20TB1F separately.; Order 1x bus module X20BM11 separately.
Diagnostics Module run/error
Yes, using LED status indicator and software
Pitch
12.5+0.2 mm
Diagnostics Open circuit
Yes, using LED status indicator and software
Power consumption Internal I/O
0.7 W
Degree of protection per EN 60529
IP20
Nonlinearity
<10 ppm
Electrical isolation
Bus isolated from analog input and strain gauge supply voltage; Channel not isolated from channel and I/O power supply
Insulation voltage between input and bus
500 Veff
Max. offset drift
15 ppm/°C
Conversion procedure
Sigma-delta
Max. gain drift
35 ppm/°C
Input protection
RC protection
Influence of cable length
Twisted and shielded conductors, cable length as short as possible, cable routing separate from load circuits, without intermediate terminal to sensor
Common-mode range
0.6 to 3.8 VDC ; Permissible input voltage range (with regard to the electric potential strain gauge GND) on inputs "Input +" and "Input -"
ADC filter characteristics
Sigma-delta, see section "Filter"
Data output rate
5000 samples per second and per channel (fDATA)
Operating range / Measurement sensor
85 to 5000 Ω
Strain gauge factor
2 to 256 mV/V, configurable using software
B&R ID code
0xE50C
Status indicators
Channel status, operating state, module status
Conversion time
200 µs
Additional power dissipation caused by actuators (resistive) [W]
+0.72
Input type
Differential, used to evaluate a full-bridge strain gauge
Digital converter resolution
24-bit
Connection
4-wire connections
I/O module
2 full-bridge strain gauge inputs

Related documents X20AIA744 Specs