X20DO4332 B&R Electronic Components

Product Details

• Temperature Operation Vertical mounting orientation
  -25 to 50°C
• Temperature Operation Horizontal mounting orientation
  -25 to 60°C
• Relative humidity Transport
  5 to 95%, non-condensing
• Relative humidity Storage
  5 to 95%, non-condensing
• Relative humidity Operation
  5 to 95%, non-condensing
• Temperature Transport
  -40 to 85°C
• Temperature Storage
  -40 to 85°C
• Temperature Derating
  See section "Derating".
• Installation elevation above sea level >2000 m
  Reduction of ambient temperature by 0.5°C per 100 m
• Installation elevation above sea level 0 to 2000 m
  No limitation
• Mounting orientation Horizontal
  Yes
• Mounting orientation Vertical
  Yes
• Power consumption Actuator power supply
  Max. 12 W
• Switching frequency Inductive load
  See section "Switching inductive loads".
• Switching frequency Resistive load
  Max. 500 Hz
• Switching delay 1 → 0
  <300 µs
• Switching delay 0 → 1
  <300 µs
• Certifications KC
  Yes
• Certifications EAC
  Yes
• Certifications HazLoc
  cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
Certifications UL
cULus E115267; Industrial control equipment
Certifications ATEX
Zone 2, II 3G Ex nA nC IIA T5 Gc; IP20, Ta (see X20 user's manual); FTZÚ 09 ATEX 0083X
Certifications CE
Yes
Certifications UKCA
Yes
Power consumption Internal I/O
0.49 W
Power consumption Bus
0.16 W
Pitch
12.5+0.2 mm
Diagnostics Module run/error
Yes, using LED status indicator and software
Degree of protection per EN 60529
IP20
Diagnostics Outputs
Yes, using LED status indicator and software (output error status)
Note
Order 1x terminal block X20TB12 separately.; Order 1x bus module X20BM11 separately.
Electrical isolation
Channel isolated from bus; Channel not isolated from channel and I/O power supply
Short-circuit proof
Yes
Insulation voltage between channel and bus
500 Veff
Peak short-circuit current
<4 A (Rev.
Voltage drop for short-circuit protection at 500 mA
Max. 2 V
Additional functions
Outputs can be connected in parallel to increase the output current.
Braking voltage when switching off inductive loads
Typ. 50 VDC
Switch-on in the event of overload shutdown or short-circuit shutdown
Approx. 10 ms (depends on the module temperature)
Voltage
Module power supply minus voltage drop for short-circuit protection
Diagnostic status
Output monitoring with 10 ms delay
Actuator power supply
0.5 A in total for output-independent actuator power supply
RDS(on)
100 mΩ (Rev.
Leakage current when the output is switched off
5 µA
Output circuit
Source
Connection type
3-wire connections
Output protection
Thermal shutdown in the event of overcurrent or short circuit (see value "Short-circuit peak current"); Internal freewheeling diode for switching inductive loads (see section "Switching inductive loads")
Nominal voltage
24 VDC
I/O module
4 digital outputs 24 VDC for 3-wire connections
Total nominal current
8 A (Rev.
B&R ID code
0x1B9C
Status indicators
I/O function per channel, operating state, module status
Switching voltage
24 VDC -15% / +20%
Additional power dissipation caused by actuators (resistive) [W]
+1.6 (Rev.
Variant
Current-sourcing FET
Nominal output current
2 A

Related documents X20DO4332 Specs