X20DO6325 B&R Electronic Components

Product Details

• Temperature Operation Horizontal mounting orientation
  -25 to 60°C
• Relative humidity Transport
  5 to 95%, non-condensing
• Temperature Operation Vertical mounting orientation
  -25 to 50°C
• Relative humidity Operation
  5 to 95%, non-condensing
• Relative humidity Storage
  5 to 95%, non-condensing
• Temperature Transport
  -40 to 85°C
• Temperature Derating
  -
• Temperature Storage
  -40 to 85°C
• Installation elevation above sea level 0 to 2000 m
  No limitation
• Switching frequency Resistive load
  Max. 2000 Hz
• Installation elevation above sea level >2000 m
  Reduction of ambient temperature by 0.5°C per 100 m
• Mounting orientation Horizontal
  Yes
• Switching frequency Inductive load
  See section "Switching inductive loads".
• Mounting orientation Vertical
  Yes
• Switching delay 0 → 1
  <100 μs
• Diagnostic status Short circuit to GND
  Detected if output ON, delay approx. 10 ms
• Diagnostic status Overload/Overtemperature
  Detected if output ON, delay approx. 10 ms
• Switching delay 1 → 0
  <300 μs
• Diagnostic status Short circuit to 24 VDC
  Detected if output OFF, delay approx. 10 ms
• Certifications KR
  Yes
Diagnostic status Open circuit
At <1 mA (typ.), detected if output OFF, delay approx. 10 ms
Certifications EAC
Yes
Certifications ABS
Yes
Certifications ATEX
Zone 2, II 3G Ex nA nC IIA T5 Gc; IP20, Ta (see X20 user's manual); FTZÚ 09 ATEX 0083X
Certifications LR
ENV1
Certifications UL
cULus E115267; Industrial control equipment
Certifications DNV
Temperature: B (0 - 55°C); Humidity: B (up to 100%); Vibration: B (4 g); EMC: B (bridge and open deck)
Certifications HazLoc
cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
Certifications UKCA
Yes
Certifications CE
Yes
Power consumption Bus
0.15 W
Power consumption Internal I/O
0.4 W
Diagnostics Diagnostic outputs
Yes, using LED status indicator and software
Diagnostics Module run/error
Yes, using LED status indicator and software
Diagnostics Status outputs
Yes, using LED status indicator and software
Degree of protection per EN 60529
IP20
Pitch
12.5+0.2 mm
Note
Order 1x terminal block X20TB06 or X20TB12 separately. ; Order 1x bus module X20BM11 separately.
Electrical isolation
Channel isolated from bus; Channel not isolated from channel and I/O power supply
Insulation voltage between channel and bus
510 Veff
Peak short-circuit current
<40 A
Switch-on in the event of overload shutdown or short-circuit shutdown
Depends on the module temperature
Braking voltage when switching off inductive loads
45 to 52 VDC
RDS(on)
150 mΩ
Leakage current when the output is switched off
<160 μA
Output protection
Thermal shutdown in the event of overcurrent or short circuit (see value "Short-circuit peak current"); Internal freewheeling diode for switching inductive loads (see section "Switching inductive loads")
Output circuit
Source
Connection type
1- or 2-wire connections
Total nominal current
3 A
Nominal output current
0.5 A
Nominal voltage
24 VDC
Switching voltage
24 VDC -15% / +20%
B&R ID code
0xE284
Status indicators
I/O function per channel, diagnostics per channel, operating state, module status
Additional power dissipation caused by actuators (resistive) [W]
Max. 0.225 W
I/O module
6 digital outputs 24 VDC for 1- or 2-wire connections with diagnostic function
Variant
Current-sourcing FET

Related documents X20DO6325 Specs