3044623 Phoenix Contact Terminal Blocks

Product Details

• Number of positions
  1
• Nominal cross section
  4 mm²
• Insulating material
  PA
• Maximum power dissipation for nominal condition
  1.02 W
• Shock protection test specification
  DIN EN 50274 (VDE 0660-514):2002-11
• Finger protection
  guaranteed
• Power frequency withstand voltage setpoint
  2.2 kV
• Setpoint
  1 N
• ECLASS 5.1
  27141100
• Number of connections
  2
• Color
  gray
• Maximum load current
  41 A (with 6 mm² conductor cross section)
• Open side panel
  Yes
• Result of surge voltage test
  Test passed
• Result of flexion and pull-out test
  Test passed
• Bending test turns
  135
• Tractive force setpoint
  80 N
• Short-time current
  0.48 kA
• Ageing test for screwless modular terminal block temperature cycles
  192
• Test frequency
  f1 = 5 Hz to f2 = 250 Hz
Note
Note. In order to use bridges, the panel on the bridge shaft must be removed.
Degree of pollution
3
Nominal current IN
32 A (with 4 mm² conductor cross section)
Back of the hand protection
guaranteed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Conductor cross section tensile test
6 mm²
Result of tight fit on support
Test passed
Tight fit on carrier
NS 32/NS 35
Test spectrum
Service life test category 2, bogie-mounted
Test directions
X-, Y- and Z-axis (pos. and neg.)
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Width
6.2 mm
Height NS 35/15
55 mm
Tightening torque, min
0.6 Nm
Conductor cross section solid max.
6 mm²
Rated surge voltage
8 kV
Overvoltage category
III
Number of levels
1
Flammability rating according to UL 94
V0
Insulating material group
I
Nominal voltage UN
1000 V
Surge voltage test setpoint
9.6 kV
Tensile test result
Test passed
Result of voltage-drop test
Test passed
Result of temperature-rise test
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Proof of thermal characteristics (needle flame) effective duration
30 s
ASD level
6.12 (m/s2)2/Hz
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Result of power-frequency withstand voltage test
Test passed
Bending test rotation speed
10 rpm
Bending test conductor cross section/weight
0.2 mm² / 0.2 kg
Result of thermal test
Test passed
Short circuit stability result
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2018-05
Test duration per axis
5 h
ETIM 3.0
EC000897
UNSPSC 6.01
30211811
UNSPSC 18.0
39121410
Acceleration
30g
Shock test result
Test passed
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Length
47.7 mm
Connection in acc. with standard
UL
Conductor cross section flexible min.
0.14 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
4 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.14 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
2.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
1.5 mm²
Surface flammability NFPA 130 (ASTM E 162)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
End cover width
2.2 mm
Stripping length
9 mm
Conductor cross section AWG max.
10
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.14 mm²
2 conductors with same cross section, stranded min.
0.14 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
2 conductors with same cross section, stranded max.
1.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 5.0
27141100
ECLASS 6.0
27141100
ETIM 7.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 21.0
39121410
Shock form
Half-sine
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Height NS 35/7,5
47.5 mm
Screw thread
M3
Conductor cross section AWG min.
26
Max. AWG conductor cross section, flexible
10
2 conductors with same cross section, solid max.
1.5 mm²
2 conductors with same cross section, solid min.
0.14 mm²
Internal cylindrical gage
A4
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 4.0
27141100
ETIM 2.0
EC000897
UNSPSC 13.2
39121410
Requirements, voltage drop
U1 ≤ 3,2 mVU2 ≤ 1,5 x U1dT ≤ 45 K
Conductor cross section short circuit testing
4 mm²
Shock duration
18 ms
Number of shocks per direction
3
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Connection method
Screw connection
Tightening torque max
0.8 Nm
Conductor cross section solid min.
0.14 mm²
Min. AWG conductor cross section, flexible
26
Conductor cross section flexible max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
4 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.14 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 4.1
27141100
ECLASS 7.0
27141120
ETIM 6.0
EC000897
UNSPSC 11
39121410
UNSPSC 19.0
39121410
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 10.0.1
27141120
ECLASS 9.0
27141120
ETIM 4.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 20.0
39121410