2904600 Phoenix Contact AC/DC Power Supplies

Product Details

• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Climatic class
  3K3 (in acc. with EN 60721)
• Dielectric strength maximum
  300 V AC 60 s
• Mains buffering time
  typ. 28 ms (120 V AC)
• Recommended breaker for input protection
  6 A ... 16 A (Characteristic B, C, D, K or comparable)
• Nominal output voltage
  24 V DC
• Selective Fuse Breaking (ISFB)
  30 A (15 ms)
• Connection in series
  yes
• Feedback voltage resistance
  ≤ 35 V DC
• MTBF (IEC 61709, SN 29500)
  > 1532000 h (25 °C)
• Insulation voltage input/output
  4 kV AC (type test)
• Conductor cross section solid max.
  1 mm²
• Conductor cross section flexible min.
  0.2 mm²
• Stripping length
  8 mm
• Standard – Limitation of mains harmonic currents
  EN 61000-3-2
• UL approvals
  UL Listed UL 508
• Depth
  125 mm
• Depth with alternative assembly
  39 mm
• Ambient temperature (start-up type tested)
  -40 °C
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
Discharge current to PE
< 3.5 mA
Power factor (cos phi)
0.82
Nominal output current (IN)
5 A
Height
130 mm
Installation distance right/left
5 mm / 5 mm
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Nominal input voltage range
100 V AC ... 240 V AC
Frequency range (fN)
50 Hz ... 60 Hz -10 % ... +10 %
AC frequency range
50 Hz ... 60 Hz -10 % ... +10 %
Nominal power consumption
163 VA
Type of protection
Transient surge protection
Connection in parallel
Yes, for redundancy and increased capacity
Protection against overvoltage at the output (OVP)
≤ 32 V DC
Output power
120 W
Power loss nominal load max.
< 17 W (120 V AC)
Protection class
I
Conductor cross section solid min.
0.2 mm²
EMC requirements for noise emission
EN 61000-6-3
HART FSK Physical Layer Test Specification Compliance
Output voltage UOut compliant
Standard - Electrical safety
IEC 61010-2-201 (SELV)
Shipbuilding approval
DNV GL, PRS, BV, LR, ABS
SIQ
BG (type approved)
Noise emission
EN 55016
Frequency range
50 Hz ... 60 Hz
Fast transients (burst)
EN 61000-4-4
Width with alternative assembly
122 mm
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Installation height
≤ 5000 m (> 2000 m, observe derating)
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Input fuse
6.3 A (slow-blow, internal)
Protective circuit/component
Varistor, gas-filled surge arrester
Dynamic Boost (IDyn.Boost)
10 A (5 s)
Residual ripple
< 30 mVPP (with nominal values)
Typical response time
300 ms (from SLEEP MODE)
Environmental protection directive
RoHS Directive 2011/65/EU
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section flexible max.
1.5 mm²
EMC requirements, power plant
IEC 61850-3
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
Standard - power supply devices for low voltage with DC output
EN 61204-3
IECEx
Ex d IIC T4...T6
Harmonic currents
EN 61000-3-2
Additional text
Test Level 2
Test field strength
110 A/m
Surge voltage load (surge)
EN 61000-4-5
Width
36 mm
Height with alternative assembly
130 mm
Installation distance top/bottom
50 mm / 50 mm
Degree of protection
IP20
Degree of pollution
2
Current consumption
1.7 A (100 V AC)
Inrush current
typ. 14 A (at 25 °C)
Setting range of the output voltage (USet)
24 V DC ... 29.5 V DC (constant capacity)
Static Boost (IStat.Boost)
6.25 A
Derating
> 60 °C ... 70 °C (2.5%/K)
Net weight
0.7 kg
Insulation voltage input / PE
3.5 kV AC (type test)
Connection method
Push-in connection
Conductor cross section AWG max.
16
EMC requirements for noise immunity
EN 61000-6-1
Standard - Safety of transformers
IEC 61558-2-16 pending
Standard - Safe isolation
IEC 61558-2-16 pending
Mains variation/undervoltage
SEMI F47-0706, EN 61000-4-11
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electrostatic discharge
EN 61000-4-2
DNV GL noise radiation
Class B
Electromagnetic HF field
EN 61000-4-3
Input
2 kV (Test Level 4 - symmetrical)
Voltage dips
EN 61000-4-11
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
Input, output (test level 1)
100 kHz 1 MHz (Test Level 3 - symmetrical)
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.
ECLASS 6.0
27049005
UNSPSC 13.2
39121004
Frequency
50 Hz
Control deviation
< 0.5 % (Static load change 10 % ... 90 %)
Maximum power dissipation in no-load condition
< 3 W (120 V AC)
Efficiency
typ. 88.8 % (120 V AC)
Insulation voltage output / PE
0.5 kV DC (type test)
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Conductor cross section AWG min.
24
Standard – Safety extra-low voltage
IEC 61010-1 (SELV)
Rail applications
EN 50121-3-2
CSA
CAN/CSA-C22.2 No. 60950-1-07
Conducted noise emission
EN 55016
DNV GL conducted interference
Class A
Contact discharge
8 kV (Test Level 4)
Comments
Criterion A
Signal
1 kV (Test Level 2 - asymmetrical)
Conducted interference
EN 61000-4-6
I/O/S
asymmetrical
Damped oscillating magnetic field
EN 61000-4-10
Test level 6
16.7 Hz 50 Hz 60 Hz (Test Level 4)
Attenuated oscillating wave
EN 61000-4-18
Signals (test level 1)
100 kHz 1 MHz (Test Level 3 - symmetrical)
ECLASS 11.0
27040701
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 7.0
27049002
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Flicker
EN 61000-3-3
Discharge in air
15 kV (Test Level 4)
Output
1 kV (Test Level 3 - symmetrical)
Voltage
2.5 kV
Voltage dip
0 %
Test level 1
15 Hz 150 Hz (Test Level 4)
Test level 2
150 Hz 1.5 kHz (Test Level 4)
Test level 4
15 kHz 150 kHz (Test Level 4)
Signals (test level 2)
100 kHz 1 MHz (Test Level 3 - asymmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 5.1
27242213
UNSPSC 20.0
39121004
Power frequency magnetic field
EN 61000-4-8
Pulse-shape magnetic field
EN 61000-4-9
Test level 3
1.5 kHz 15 kHz (Test Level 4)
Input, output (test level 3)
100 kHz 1 MHz (Test Level 3 - asymmetrical)
REACh SVHC
Lead 7439-92-1
ECLASS 10.0.1
27040701
ECLASS 9.0
27040701
UNSPSC 19.0
39121004
UNSPSC 18.0
39121004
Number of periods
0,5 / 1 / 5 / 50 / 250 periods
Asymmetrical conducted disturbance variables
EN 61000-4-16
Test level 5
16.7 Hz 50 Hz 60 Hz (Test Level 4)
Input, output (test level 2)
10 MHz
Criterion A
Normal operating behavior within the specified limits.
ETIM 6.0
EC002540
UNSPSC 21.0
39121004