2904605 Phoenix Contact AC/DC Power Supplies

Product Details

• Depth
  90 mm
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Degree of pollution
  2
• Input voltage range
  100 V AC ... 240 V AC -15 % ... +10 %
• Current consumption
  0.44 A (100 V AC)
• Inrush current
  typ. 11.3 A (at 25 °C)
• Nominal output voltage
  12 V DC
• Protective circuit/component
  Varistor
• Feedback voltage resistance
  ≤ 25 V DC
• Residual ripple
  < 30 mVPP (with nominal values)
• Maximum power dissipation in no-load condition
  < 0.4 W (230 V AC)
• Insulation voltage input/output
  4 kV AC (type test)
• Conductor cross section solid max.
  2.5 mm²
• Conductor cross section AWG min.
  24
• Width
  22.5 mm
• Installation distance right/left (active)
  15 mm / 15 mm (POut ≥50% )
• Degree of protection
  IP20
• Protection class
  II
• Conductor cross section flexible min.
  0.2 mm²
• Conductor cross section AWG max.
  14
Standard - Safe isolation
IEC 61558-2-16
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Noise emission
EN 55016
Frequency range
50 Hz ... 60 Hz
Discharge in air
15 kV (Test Level 4)
Output
1 kV (Test Level 3 - symmetrical)
I/O/S
asymmetrical
Voltage dips
EN 61000-4-11
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 7.0
27049002
UNSPSC 18.0
39121004
Height
106 mm
Installation distance top/bottom (active, passive)
30 mm / 30 mm (POut ≤50 %)
Installation distance top/bottom (passive)
30 mm / 30 mm (POut ≥50% )
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Discharge current to PE
< 0.25 mA (264 V AC, 60 Hz)
Nominal power consumption
32.8 VA
Type of protection
Transient surge protection
Static Boost (IStat.Boost)
3.125 A (≤ 40 °C)
Output power
30 W
Typical response time
500 ms
Net weight
0.181 kg
MTBF (IEC 61709, SN 29500)
> 1848000 h (25 °C)
Conductor cross section solid min.
0.2 mm²
Standard - Safety of transformers
EN 61558-2-16
Stripping length
10 mm
SIQ
CB-Scheme (IEC 61010-1, IEC 61010-2-201)
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Electrostatic discharge
EN 61000-4-2
Test field strength
1000 A/m
Signal
0.5 kV (Test Level 2 - symmetrical)
Voltage dip
0 %
Test level 1
16.67 Hz 50 Hz 60 Hz 150 Hz 180 Hz (Test Level 3)
ECLASS 11.0
27040701
ETIM 7.0
EC002540
UNSPSC 20.0
39121004
Installation distance right/left (passive)
5 mm / 5 mm (POut ≥50% )
Installation distance top/bottom (active)
30 mm / 30 mm (POut ≥50% )
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Installation height
≤ 5000 m (> 2000 m, observe derating)
Mains buffering time
typ. 54 ms (120 V AC)
Recommended breaker for input protection
6 A ... 16 A (Characteristic B, C or comparable)
Nominal output current (IN)
2.5 A
Connection in parallel
Yes, for redundancy and increased capacity
Connection in series
yes
Control deviation
< 0.2 % (Static load change 10 % ... 90 %)
Power loss nominal load max.
< 3.5 W (120 V AC)
Efficiency
typ. 89.5 % (120 V AC)
Connection method
Push-in connection
Conductor cross section flexible max.
2.5 mm²
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
UL approvals
UL Listed UL 61010-1
Harmonic currents
EN 61000-3-2
Contact discharge
8 kV (Test Level 4)
Input
2 kV (symmetrical)
Frequency
60 Hz
Number of periods
0.5 / 1 / 5 / 50 periods
Attenuated oscillating wave
EN 61000-4-18
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.
ECLASS 6.0
27049000
ETIM 6.0
EC002540
UNSPSC 21.0
39121004
Installation distance right/left (active, passive)
0 mm / 0 mm (POut ≤50 %)
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Climatic class
3K3 (in acc. with EN 60721)
Dielectric strength maximum
300 V AC 60 s
Frequency range (fN)
50 Hz ... 60 Hz -10 % ... +10 %
Input fuse
3.15 A (slow-blow, internal)
Setting range of the output voltage (USet)
12 V DC ... 15 V DC (constant capacity)
Dynamic Boost (IDyn.Boost)
4.5 A (≤ 60 °C (5 s))
Protection against overvoltage at the output (OVP)
≤ 18 V DC
Fast transients (burst)
EN 61000-4-4
Surge voltage load (surge)
EN 61000-4-5
Voltage
1 kV (symmetrical)
Additional text
Test Level 2
Pulse-shape magnetic field
EN 61000-4-9
Test level 2
16.67 Hz 50 Hz 60 Hz (Test Level 2)
ECLASS 5.1
27242213
ECLASS 9.0
27040701
UNSPSC 19.0
39121004
Standard – Safety extra-low voltage
IEC 61010-1 (SELV)
Conducted noise emission
EN 55016
Flicker
EN 61000-3-3
Electromagnetic HF field
EN 61000-4-3
Comments
Criterion A
Conducted interference
EN 61000-4-6
Power frequency magnetic field
EN 61000-4-8
Asymmetrical conducted disturbance variables
EN 61000-4-16
Criterion A
Normal operating behavior within the specified limits.
ECLASS 10.0.1
27040701
UNSPSC 13.2
39121004